Volume is indexed by Thomson Reuters CPCI-S (WoS). This collection addresses specific topics within the field of stress measurement in solids using neutrons, X-rays and synchrotron radiation. Particular attention is paid to multidisciplinary approaches involving an understanding of the measured stress field and the implications of the stress field for the behaviour of materials and components.

Table of Contents:
Committees Preface Evening Lecture The Early History of Neutron Stress Measurements Chapter 1. PROCESSING Determination of Residual Stress Distribution in Severe Surface Deformed Steel by Shot Peening Variation of Residual Stresses in Drawn Copper Tubes Experimental Investigation of Residual Stresses after Heat Treatment and Grinding Processes in the Production of Ball Bearing Rings Mechanical and Physical Analysis of Alloys Samples Produced with a New High Centrifugal Rate Machine Influence of Microstructural Parameters on Macroscopic Residual Stress Analysis of Complex Materials by Neutron Diffraction Methods Residual Stress and Microstructural Variations in Thick Aluminium Alloy Forgings Effect of Varying Cold-Drawing Deformation on Residual Stresses Measured by Neutron Diffraction in Steel Rods Application of Neutron Diffraction Technique to Industrial Materials Neutron Strain Investigations of Laser Bent Samples Residual Stress in a-Brass during Annealing Chapter 2: PLASTICITY Rod-Textured Zircaloy-2: A Case Study of an Anisotropic Metal with Multiple Deformation Modes, Strong Texture and Thermal Strains Instrumented Indentation Testing on Uniaxially Prestressed Steel Samples In Situ Analysis of Deformation Mechanisms of Cu-Based fcc Materials under Uniaxial Loading Evaluation of the Residual Stresses and Determination of the Proportion of Residual Austenite in an Austempered Ductile Iron Having Undergone Thermo Mechanical Treatments Temperature Dependence of Residual Stress Gradients in Shot-Peened Steel Coated with CrN In Situ Neutron Diffraction Studies of the Pseudoelastic-Like Behaviour of Hydrostatically Extruded Mg-Al-Zn Alloy A Study of Residual Elastic Strain Distribution in an AZ91 Mg Alloy Bar Loaded in Four Point Bending Investigation of the Stress Fields Around a Fatigue Crack in Aluminium Alloy 5091 Study of Elasto-Plastic Anisotropic Response of Stainless Steel Weld Metal Using Neutron Diffraction Neutron Diffraction Analysis of Stresses in an In-Plane Biaxially-Fatigued Stainless Steel Sample of Cruciform Geometry Neutron Diffraction Measurement and Finite Element Modelling of Residual Strains Due to Bath and Spray Quenching of AISI 316L Stainless Steel Cylinders Stored Energy of Plastic and Elastic Origin and Recrystallization Development of Intergranular Stresses during In Situ Compression Tests in Zircaloy-4 Chapter 3: METHODS Monte Carlo Simulation to Macro Stress Evaluation and Micro Strain Analysis by Neutron and Synchrotron Radiation Diffraction Neutron Diffraction Study of a New Generation of Implants Investigation of Retained Strains and Microstructures for a Hot Deformed Stainless Steel Neutron Diffraction Study of Duplex Stainless Steel during Loading at 200°C Single-Line Diffraction Profile Analysis Method Used for Evaluation of Microstructural Parameters in the Plain Ferritic Steel upon Tensile Straining Improvements in Energy Dispersive Diffraction in Respect of Residual Stress Analysis In Situ Investigation of the Deformation Behaviour of the Wrought Mg Base Alloy AZ31 Using Energy Dispersive Synchrotron Diffraction First Results of the DITO-Experiment at the HARWI II Beamline at GKSS/DESY Diffraction Contrast Tomography - A Synchrotron Radiation Technique for Mapping Polycrystalline Microstructures in 3D Kowari – The Residual-Stress Diffractometer for Engineering Applications at OPAL A Critical Discussion of the sin2? Stress Measurement Technique Measurement of all Six Components of X-Ray Elastic Factors Use of Stored Energy Distribution in Stochastic Vertex Model Imaging Diffraction Using Maxim at G3/Hasylab - Spatial Resolved Strain Measurements on Linear Friction Welded Dissimilar Materials (AA7020-T6/Ti6AlV Two-Dimensional Mapping of Crack-Face Bridging Stresses in Alumina Using Synchrotron Micro X-Ray Beam Application of Synchrotron Radiation to Residual Stress Analysis by IP/cosa Method Influence of Peak Determination Method on Area Detector Type Neutron Stress Measurement The High Energy Materials Science Beamline at PETRA III Measurement of Internal Strain in Materials Using High Energy White X-Ray at SPring-8 Inter-Granular Residual Stresses in Polycrystalline Aggregates: Finite Element Modelling and Diffraction Post-Processing Experimental/Modelling Study of Residual Stress in Al/SiCp Bent Bars by Synchrotron XRD and Slitting Eigenstrain Methods Problems in the Averaging of Neutron Diffraction Stress Data from Round-Robin Campaigns Corrections for Residual Stress in X- Ray Grazing Incidence Technique Analysis of Residual Stresses Around ‘Dimpled’ Cold-Expanded Holes in Aluminium Alloy Plates Chapter 4: CERAMICS X-Ray Powder Diffraction Characterization of Residual Stresses and Strains in Y3Al5O12:Nd3+ Nanoceramics Neutron Diffraction Studies of Residual Stresses in Functionally Graded Alumina/Zirconia Ceramics Through-Thickness Residual Stress Measurement in Metal and Ceramic Spray Coatings by Neutron Diffraction Measurement of Strain Distribution around Weld Zone for Railway Carbody Structure Using High-Energy Synchrotron Radiation Residual stresses in Al2O3/Y-TZP Ceramic Laminates Fabricated by Tape and Slip Casting Distribution of Residual Stresses in EB-PVD Thermal Barrier Coatings In Situ Synchrotron Measurement of Internal Stresses in Solid-Oxide Fuel Cell during Red-Ox Cycle Chapter 5: WELDS Study of Microstructure and Residual Stresses in Dissimilar Al/Steels Welds Produced by Cold Metal Transfer Analysis of Residual Stress in Laser Welded Aerospace Aluminium T-Joints by Neutron Diffraction and Finite Element Modelling Microstructure and Residual Stresses in Dissimilar Mg-Al-Zn-Alloy Single Overlap Laser Beam Welds Study of Residual Stress Distribution in a Stainless Steel Bead-on-Plate Simulation Benchmark Sample Influence of the Welding Sequence on Residual Stresses in Laser Welded T-Joints of an Airframe Aluminium Alloy Residual Stress Analyses by Neutron Diffraction in Irradiated Double-V Butt Welded Steel Plates Residual Stresses in High Strength, Thick Section Steel Welds In Situ Monitoring of Weld Transformations to Control Weld Residual Stresses Chapter 6: COMPOSITES SXRD Measurements of Residual Stresses in Sintered Diamond–Cobalt Composites Synchrotron Energy-Dispersive X-Ray Diffraction Analysis of Residual Strains around Friction Welds between Dissimilar Aluminium and Nickel Alloys Residual Stresses and Void Kinetics in AlSiC MMCs during Thermal Cycling Chapter 7: THIN FILMS Position Resolved Residual Stress Determination in Alumina-Zirconia Multilayered Ceramics